SOLD!!!! 1979 North American C-20, '03 150 HPDI, completely redone 2008! SOLD !!!!

over 4 years ago
SOLD!!!! 1979 North American C-20, '03 150 HPDI, completely redone 2008! SOLD !!!!
North American
Available on

Ok here she is. I just upgraded to a newer, larger, more flyfishing friendly platform. Ill list out the work that was done since I owned it. All work performed from late spring of 2008, up to the late spring of 2009. EVERYTHING on the boat was either replaced, or reconditioned. The only thing not replaced, was the actual hull. All items listed were installed brand new, unless stated otherwise.
**$9900** Trailer available for $1000 (single axle galvanized roller- 2005 Venture)
Hull: 1979 North American 20' CC
Engine: 2003 Yamaha 150HP HPDI
Engine Components:
Yamaha Reliance stainless steel prop 17" pitch
Yamaha Control cables
Yamaha Digital tachometer
Yamaha analog fuel level gauge
Yamaha key switch and engine harness'
Yamaha 704 Premium binnacle control box
Yamaha oil tank (mounted in a battery box- for cleanliness)
Yamaha 10 micron water separating fuel filter
All wiring redone with Ancor tinned copper marine grade wire, and Ancor marine grade connectors
Lenco 12x12 edge mount trim tabs
Lowrance 520i Hi-def GPS/FF (in hull transducer, external transom mounted temp sensor)
Dual batteries (group 27/1000 CCA) with Blue Seas dual battery switch and all new battery cables and lugs
Perko LED underwater lights (2)
Blue Seas 6 switch panel (water proof circuit board)
Blue Seas fuse panel
Rule 750GPH bilge pump
Rule 40A float switch
Rule 800GPH Tournament live well pump
New Attwood bow and stern light
Hella LED courtesy lights (2)
Boat Components:
New transom installed (marine grade 3/4" plywood, 12 gallons vinyl ester resin)
Fresh Dupont Emron paint, insids and out (non-skid applied to decks)
Bimini Blue exterior and floor, Oyster white inside accents
Hydra Sports rub rail
Aqua World 32 gallon counter clockwise flow livewell (internal spray bar)
Pop-up cleats (4)
Teleflex Seastar hydraulic steering helm, ram, and hoses
Stiffy Push Poles fiberglass console and windshield (44" bridge clearance)
Console mounted rod holders (3 standard, 1 fly)
Gunwale rod holders (4)
New leaning post and cushion, with custom rocket launchers (4)
Large fiberglass dry storage box/seat with new cushion (2009), in front of console
New fuel tank summer of 2006, (tank removed, cleaned, inspected, and painted 2008)
New Tempo fuel sender
Forward storage compartment floor hatch reconditioned (new under-bracing, hinges, handle, and seals)
All new stainless hardware in 2008 (deck screws, cleats, hatch hinges, bow chocks, fender hooks and eyes)
All new hoses and clamps for bilge pump, live well, deck drains, and fuel tank components installed in 2008
TH Marine rigging tube and base
TH Marine scupper ball drains
TH Marine deck plates and hatches
Engine Maintenance Performed:
New water pump and thermostats
New VST filter, primary fuel filter, and high pressure filter
Fresh gear oil, lower unit repainted
New NGK spark plugs
New oil filter on remote oil tank
All new zincs on bracket and lower unit
Injectors and high pressure pump rebuilt and cleaned by Flagship Marine in winter of 2007/2008
I have MANY more pictures avail. I took a lot of pictures of the entire build process. From the day I bought the boat, from cutting the transom open, the entire paint process, wiring process, to sitting on the trailer on the way to the gas station for the initial fuel up. I didnt want to post up over 100 photos on this thread....